FM Midi Synthesizer with Pd on Raspberry Pi

Here’s a simple FM Midi synthesizer developed in pd running on a Raspberry Pi. The patch was written and tested on a Macbook, then the patch file is uploaded to RPi and run using pd-extended from the command line. For example the command to run this patch is:

pd-extended -nogui -noadc -midiindev 1 piSynth1.pd

[todo: upload patch to this site. Currently in tkzic/rpi/pd/piSynth1.pd]

[udpate]: when trying this again, a few problems came up:

  1. R-Pi didn’t recognize sound card/midi: Solution was to connect the sound card directly to the R-Pi USB port and connect the Midi controller via powered USB hub
  2. Sometimes pd-extended errors out with a device busy message. Seems to run ok if you press ctrl-c and repeat the pd-extended command line. I think this problem may be due to a previous process hanging – and not exiting cleanly

 

 

 

Pd synth examples

notes

A collection of Pd synth patches that might run on Raspberry Pi.

 

bluetooth with Raspberry-Pi

notes

Raspberry Pi with Pd: audio test

notes

In an audio pass-through test using Pd, with a USB sound card (Griffin iMic), the maximum stereo sample rate before ‘breakup’ is 32000.In mono, it sounds “ok” at 44100. Latency seems low enough to use for music but I’m too sleepy to figure out the numbers.

I don’t know enough about Linux audio to say if the performance deficit is due to ALSA drivers, the sound card, background processes, pd, the CPU, or what?Anyway I ‘m guessing R-Pi will spawn interesting synths and lo-fi FX processors. They’re cheap enough you could use them in parallel.

Prediction: They’ll double the speed, and sell a million more by the end of the year. We’ll see a range of ‘Pi’ clones which run the same Linux distributions, but offer various speeds and IO options. It feels like the democratization of manufacturing has taken another huge leap.

pd-extended on Raspberry Pi

notes

Using installation instructions from Pd site:

http://puredata.info/downloads/pd-extended-0-43-3-on-raspberry-pi-raspbian-wheezy-armhf

Installation worked fine. I tried running the GUI under xterm and it was a disaster. Then, using this post, I was able to get a test patch (sine wave with LFO) running in terminal mode:

http://log.liminastudio.com/programming/running-puredata-on-the-raspberry-pi

Note: I changed the actual command to this due to the fact I’m running pd-extended and a USB sound card:

pd-extended -nogui -noadc testPatch.pd

This post from same source has instructions for installing pd-extended (disaster) but a very nice version of the test patch called testPatchExtended.pd

http://log.liminastudio.com/writing/tutorials/how-to-build-pd-extended-on-the-raspberry-pi

(another update) running Midi:

To run midi you need to specify the device on the command line. First I plugged in the m-audio key station 49 and rebooted RPi

To get a list of devices use:

pd-extended -nogui -listdev

Then to run a patch with midi

pd-extended -nogui -noadc -midiindev 1 testMidi.pd

Here is a page with more information on command line options

http://crca.ucsd.edu/~msp/Pd_documentation/x3.htm#s4

(another update) Testing with Griffin iMic. Bad news when doing an ADC->DAC passthrough, sample rates above 32000 don’t work in stereo. However 44100 and 48000 sound fine in mono.

At the higher rates in stereo, the audio breaks up. Oh well. Need to try the Behringer audio box, but I’m assuming there will be no difference. Only possibility would be to somehow devote more system resources to audio.

raspberry pi – external sound card sucess

Installed a Griffin iMic USB sound card on Raspberry Pi today.

Here’s how:

  • plug in imic
  • Edit alsa  config file so that imic is default sound cart
  • test

Details

For editing alsa, follow instructions at beginning of this post for editing /etc/modprobe.d/alsa-base.conf 

But you can stop following the instructions after the first reboot.

http://www.jackenhack.com/raspberry-pi-usb-audio-quality-problems/

For testing, use this command:

sudo aplay /usr/share/sounds/alsa/Front_Center.wav